咨询热线:

400-0733-598

深圳市创盈时代科技有限公司

联系人:汪菲菲

电话:0755-81779389

手机:18819037886

QQ:2764836233

Email:chytime@chytime.com

地址:深圳市沙井沙一社区万安路长兴科技园16栋2楼

您所在的位置:首页 > 技术文库 > 焊锡机技术文章 >

DC头自动焊锡机常见的故障及排除方法

发布时间:2018-03-03 10:17:54   来源:本文搜集于网络,由DC头自动焊锡机厂家创盈时代整理并发布,欢迎转载    点击:

随着人工成本的不断增加,很多线材企业都采用了DC头自动焊锡机代替人工焊锡数据线,以此来提升焊锡的效率。那么DC头自动焊锡机常见的故障及排除方法有哪些呢?
With the increase of artificial cost, many wire rod enterprises have adopted the DC head automatic soldering machine instead of the artificial solder data line to improve the efficiency of the solder. So what are the common troubleshooting and troubleshooting methods for DC head automatic soldering machines?
DC头自动焊锡机

1.分线、剥皮不良。首先确认链条是否到位(夹线槽对准分线刀槽),保证放线要到位,分线定位刀的灵活,分线定位刀中间的压线压块的力度要适中。
1. dividing lines and bad peeling. First, confirm whether the chain is in place (the clamp line is aligned to the dividing line tool slot), ensure the location of the wire should be in place, the location of the positioning tool is flexible, and the strength of the pressing block in the middle of the positioning tool is moderate.

2.半剥不良。如果剥不掉外皮和断铜丝的时,需要上下调节气缸,半剥后退时动作一定要快一点。
2. half undesirable peeling. If you do not peel off the outer skin and break the copper wire, you need to adjust the cylinder up and down, and the action must be faster when half stripping back.

3.焊接不良。气缸上下动作配合一定要适当,同时端子一定要在Y型分线的中心点,DC头自动焊锡机的焊枪嘴位置一定要对准确,也要注意控制焊枪嘴压端子的力度,焊枪左右移动速度一定要平稳。
3. bad welding. The coordination of the upper and lower cylinders must be proper. At the same time, the terminals must be at the center point of the Y type sub line. The position of the welding nozzle of the DC head automatic solder machine must be accurate, and the intensity of the welding tip pressure terminals must be controlled. The speed of the welding gun moving must be smooth.

4.焊接不沾锡。用振动盘平送时,一定要清洗振动盘,保持振动盘干净,同时检查烙铁的温度是否达到要求,从而解决自动焊锡机不沾锡的问题。
4. no tin in welding. When vibrating disk is sent flat, it is necessary to clean the vibration tray, keep the vibration disk clean, and check whether the temperature of the iron meets the requirements, so as to solve the problem that the automatic solder machine does not touch the tin.

5.不焊接:检查光纤感应器的位置是否对齐,光纤放大器指示灯是否正常。
5. non welding: check whether the position of the optical fiber sensor is aligned, and the optical fiber amplifier indicator is normal.

以上就是DC头自动焊锡机常见的故障及排除方法的一些介绍,DC头全自动焊锡机能够代替人工自动分线焊线,每小时焊接DC端子可达1300头,很大程度上提升了线材企业焊接的效率,保证了焊接的质量,为线材企业创造了更多的效益。
Some of the above is the automatic soldering machine head DC common faults and exclusion method, DC head automatic soldering machine can replace manual automatic wire welding line, the welding terminal up to 1300 DC per hour, largely enhance the efficiency of business wire welding, ensure the welding quality, create more benefits for the wire enterprise.

多关于焊锡机的小知识请关注焊锡机厂家创盈时代,我们是一家专注于双Y双头焊锡机、双头三头焊锡机、三轴四轴焊锡机、激光焊锡设备整体解决方案的高新技术企业。

原文地址:http://www.chytime.com/news/hxjs/1709.html

本文关键字:DC头自动焊锡机故障

本文由www.chytime.com 深圳创盈时代科技有限公司 自动点胶机整理,欢迎转载,转载时请标明出处。

上一篇:焊锡机日常操作要领介绍
下一篇:最后一页