咨询热线:

400-0733-598

深圳市创盈时代科技有限公司

联系人:汪菲菲

电话:0755-81779389

手机:18819037886

QQ:2764836233

Email:chytime@chytime.com

地址:深圳市沙井沙一社区万安路长兴科技园16栋2楼

您所在的位置:首页 > 技术文库 > 点胶机技术文章 >

全自动点胶机更换胶管要注意这几点细节

发布时间:2018-08-18 10:24:42   来源:本文搜集于网络,由全自动点胶机厂家创盈时代整理并发布,欢迎转载    点击:

在更换胶管时,留心不要把空气引入到胶体通道中。万一胶管中有空气残留,而你又判定空气没有经过胶管进入点胶泵中,则请按下列过程更换胶管:
When replacing the hose, be careful not to introduce the air into the Colloid channel.If there is air residue in the hose, and you decide that the air has not been through the rubber tube into the dispensing pump, please replace the hose according to the following procedure:

全自动点胶机  

关闭点胶机,打开门,从胶管上卸下冷却套,万一有冷却套。卸下气压头。撤消胶管。请承认90°的弯管配件还附着在点胶阀上,万一有弯管配件。胶管卸下后,点胶阀断定转接头底部会发作一小段空腔。请运用旧胶管中的胶体填充这段空腔,并检查断定转接头中是否存在气泡。
Turn off the dispensing machine. Open the door and remove the cooling sleeve from the hose, in case there is a cooling sleeve. Remove the air pressure head. Remove the hose. Please acknowledge that the bend fittings at 90° are also attached to the dispensing valve, in case there is a bend fitting. After the hose is unloaded, the dispensing valve determines that the bottom of the adapter will attack a small cavity.Use the colloid in the old hose to fill the cavity and check to see if there is a bubble in the adaptor.

万一有气泡,请运用新的胶管填充这段空腔,并检查新的胶管是否存在气泡。万一有气泡存在的话,请运用另一个胶管。卸下新胶管的盖帽。坚持胶管结尾向下,让胶体彻底地填满胶管底部,联接胶管和点胶阀断定转接头。万一胶体溢出到配件外,请擦拭洁净。重新安装气压头。重新安装胶管冷却套,万一有冷却套。关闭点胶机门。重新启动设备。
In the event of a bubble, fill the cavity with a new hose and check to see if there is a bubble in the new hose. If there is a bubble, please use another hose. Remove the cap from the new hose. Adhere to the end of the hose, let the colloid thoroughly fill the bottom of the hose, connecting the hose and dispensing valve to determine the adapter. If the colloid overflows to the accessory, please wipe clean. Reinstall the air pressure head. Reinstall the hose cooling sleeve in case there is a cooling sleeve. Close the glue machine door. Reboot the device.

全自动点胶机排胶要留有成分的时刻,使新胶管中的胶体顺利流出点胶头,承认点胶阀的压力和速度依照志向情况设定。然后测定胶体流速,直至接连两次丈量成果的过失在正负2%规划以内。另外还需要留心一点,万一存在下述情况,建议不要运用简易的胶管更换方法:点胶机在运转过程中,胶管中胶材现已用完。该情况下点胶阀中很可能有空气存在。胶管中的胶材现已超过了运用期限。呈现以上任何情况,你有必要彻底清洁并单调点胶阀或点胶泵,并遵照装备过程。
Automatic dispensing glue machine to leave the ingredients of the moment, so that the new hose in the gel smooth out of the point of the plastic head, the recognition of the pressure and speed of dispensing valve in accordance with the aspirations of the setting. The colloid flow rate is then measured until the fault of two consecutive measurements is within plus or minus 2%. Also need to pay attention to, in case of the following circumstances, it is recommended not to use a simple rubber tube replacement method: Dispensing machine in the running process, rubber tube in the plastic material has been used up. In this case, there is likely to be air presence in the dispensing valve. The plastic material in the hose has now exceeded the application period. In any of these cases, you need to thoroughly clean and dull the dispensing valve or dispensing pump and follow the equipment process.

深圳市创盈时代科技有限公司是一家专注于平台点胶机,落地式点胶机,视觉点胶机,非标自动化设备的研发生产和销售于一体的国家高新技术点胶机厂家。

本文关键字:点胶机换胶管

原文地址:http://www.chytime.com/news/djjs/1754.html

本文由www.chytime.com 深圳创盈时代科技有限公司 自动点胶机整理,欢迎转载,转载时请标明出处。

上一篇:选择全自动点胶机应该注意的三要素
下一篇:最后一页