咨询热线:

400-0733-598

深圳市创盈时代科技有限公司

联系人:汪菲菲

电话:0755-81779389

手机:18819037886

QQ:2764836233

Email:chytime@chytime.com

地址:深圳市沙井沙一社区万安路长兴科技园16栋2楼

您所在的位置:首页 > 技术文库 > 点胶机技术文章 >

全自动点胶机对点胶工艺的要求有哪些?

发布时间:2018-07-25 16:35:03   来源:本文搜集于网络,由全自动点胶机厂家创盈时代整理并发布,欢迎转载    点击:

点胶机作为一种常用的工业设备被广泛的应用于医药,化工,电子等领域,但是对于点胶机的工艺要求有哪些呢?今天自动点胶机厂家创盈时代的技术人员就详细的为大家解读一下。
Dispensing machine, as a common industrial equipment, has been widely used in medicine, chemical industry, electronics and other fields. But what are the technological requirements for dispenser? Today, the technicians of the automatic dispensing machine factory create a detailed interpretation for you.

全自动点胶机

1.所用胶水的混合比例。任何一种点胶机对胶水的混合比例都有一个范围,常见的有100:100到100:10,如果所用的胶水不在这个范围,那就要重新考虑了。
The mixing ratio of 1. used glue. Any kind of glue dispenser has a range of mixing ratio for glue. It is common from 100:100 to 100:10. If the glue is not in this range, it should be reconsidered.

2.胶水里面有没有填料,如氧化铝,氧化硅,石英砂,陶瓷等。如果有填料,在选用双液点胶机时,就需要谨慎考虑。双液点胶机控制出胶量的方式有两种,一种是通过齿轮泵,一种是通过螺杆泵!齿轮泵在遇到含有填料的胶水时,时间久了易磨损,进而造成出胶量不准,混合比例不精确,出现点出来的产品长时间不干。螺杆泵相比较而言,较耐磨损一些,这些可参考一下这两种泵的资料!
Is there any filler in glue, such as alumina, silica, quartz sand, ceramics and so on. If there is filler, when selecting two liquid dispensers, we need to consider carefully. There are two ways to control the amount of glue. One is through the gear pump and the other is through the screw pump. The gear pump is easy to wear for a long time when it meets the glue containing the stuffing. Then, the quantity of the glue is not allowed, the proportion of the mixing is not accurate, and the product that comes out is not dry for a long time. Compared with the screw pump, it is more resistant to wear. These can refer to the information of these two pumps.

3.所要点的产品,每次最小的点胶量是多少,比如你要点的产品是1克,胶水配比是10:1,那相当于B胶的出胶量要达到0.1克,机器的最小出胶量是多少,你买机器时就要对比比较,看能否达到要求!
Main points of the product, the minimum amount of glue each time, such as your key product is 1 grams, the glue ratio is 10:1, that is equivalent to the glue quantity of B glue to reach 0.1 grams, the minimum quantity of machine glue is how much, when you buy the machine compare comparison, see whether to meet the requirements!

4.生产的产量,量大的话可考虑带XYZ机械手,或者多并头的点胶机,量小的话,用单头,甚至不带XYZ机械手的都可完成。点胶工艺的要求,要不抽真空,将胶水里面的气泡抽出。
The output of the production, the large amount of words can take into account with the XYZ manipulator, or multi side of the glue machine, small amount of words, with a single head, or even without a XYZ manipulator can be completed. The requirement of dispensing process is to evacuated the bubbles in the glue without vacuuming.

深圳市创盈时代科技有限公司是一家专注于平台点胶机,落地式点胶机,视觉点胶机,非标自动化设备的研发生产和销售于一体的国家高新技术点胶机厂家。

本文关键字:点胶机工艺要求

原文地址:http://www.chytime.com/news/djjs/1746.html

本文由www.chytime.com 深圳创盈时代科技有限公司 自动点胶机整理,欢迎转载,转载时请标明出处。

上一篇:自动点胶机的日常保养应该怎样做
下一篇:最后一页